2n M2M Solution 2N SmartCom - User Manual 1.9.0 Uživatelský manuál Strana 79
- Strana / 149
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
792N TELEKOMUNIKACE a.s., www.2n.cz
®
7.1 SC Server
2N SmartCOM
®
Server is an application necessary for the Control2N SmartCOM
®
Panel operation, providing communication between the Control Panel2N SmartCOM
®
and the terminal.
Caution
The Server must be installed on a PC accessible from2N SmartCOM
®
a public Internet. Or, a NAT rule has to be defined to provide access to
such PC. Otherwise, the terminals cannot be connected to the 2N
®
Server. You can select the ports to be forwarded to your SmartCOM
LAN via the NAT during installation.
Installation
Once launched, the installation program will scan your PC. If it finds another 2N
®
Server version, it will ask you whether to uninstall. If you select No, the SmartCOM
wizard will be terminated. If you select Yes, the current Server2N SmartCOM
®
version will be removed. Then you will be asked whether or not to remove the
configuration files. If you select No, the current configuration will be retained and the
application will only be updated.
Now the Server Setup Wizard is launched. Follow the wizard2N SmartCOM
®
instructions. Select the directory for the Server to be installed. By2N SmartCOM
®
default, C:\Program Files\ SC Server is2N TELEKOMUNIKACE\2N SmartCOM\
® ®
used.
Also select the port for the application to communicate with the terminals and other 2N
Control Panel applications. Make sure that the port is accessible from the SmartCOM
®
Internet (see above) and properly configured in all terminals and applications. Http
accessibility is necessary as the selected port provides a listing of LOG files and can be
used for firmware downloading to terminals. Firmware is downloaded whenever
upgrade is initiated by the Control Panel or the address is entered2N SmartCOM
®
into the terminal.
Here you can also set the port for the AT API; refer to S. 8 for details. Now the wizard
is ready to install the Server. It displays the list of settings. Check the2N SmartCOM
®
set parameters carefully as the values cannot be changed without reinstallation when
the installation has been completed! If you find an error, push the button toBack
return to the respective window. If all the settings are OK, push to continue.Install
The wizard now installs the Server. Server2N SmartCOM
®
The 2N SmartCOM
®
service is launched automatically after installation. If the automatic launch fails for any
reason, launch the service manually. Now the Server is ready for2N SmartCOM
®
use.
- 2N SmartCom 1
- 1. Product Overview 5
- 1.1 Product Description 6
- 1.2 Upgrade 8
- 1.3 Terms and Symbols Used 9
- 2.1 Basic Version Description 11
- 2.2 PRO Version Description 13
- 2.3 Before You Start 15
- 2.4 Mounting 16
- 3. Function and Use 19
- 3.1 Putting in Operation 20
- 3.2 GSM LED Indicator 21
- 3.3 Input and Output Circuits 22
- Output Circuits 23
- IP Access 24
- Real Time Clock 25
- Wireless M–Bus Interface 25
- ZigBee Interface 26
- 3.4 Input Calibration 27
- 4. Configuration by Terminal 29
- 4.1 Configuration 30
- 2N SmartCOM GSM Commands 32
- Port 1 (RS 232) SC Commands 34
- Relay Outputs 36
- ADC – Input Circuits 38
- S0 – Pulse Counting 41
- General Commands 43
- Test Command 46
- 5. Configuration by SMS 58
- INFO SMS 59
- Basic Settings 60
- Relay Control 62
- Error Replies 64
- 6. Terminal Config 66
- Application Details 67
- Application Use 70
- Figure: Ethernet Menu 71
- Figure: IP Access Menu 77
- 7. Control Panel 78
- 7.1 SC Server 79
- Licencing 80
- 7.2 Control Panel 82
- Introduction to Application 84
- Figure: Application Window 85
- Basic Controls 86
- 7.3 Control Panel Use 88
- Connections 90
- Virtual Ports 92
- Settings 94
- Admin Mode 96
- Terminals 99
- Server Settings 101
- Firmware Management 103
- 8. AT API 107
- 8.1 AT API Description 108
- 8.2 Supported Commands 109
- Terminal Connection 111
- Terminal Communication 111
- Port Settings 112
- Terminal Data Reading 113
- 9. User Defined Functions 117
- 9.1 UDF Description 118
- 9.2 UDF Condition Setting 119
- Action Types 121
- Action Parameters 123
- Counters 125
- Error Codes 125
- 10. sc_config 128
- Database Export and Import 129
- Setting Options 130
- 11. Maintenance 134
- 11.2 Factory Default Reset 136
- 11.3 Repairs 137
- 12. Technical Parameters 138
- Power Supply 139
- Relays (Two) 139
- Input Circuits to ADC (Two) 140
- RS232 Interface 140
- Working Conditions 140
- CE certificate 143
- 13. Supplementary 144
- Information 144
- 13.1 List of Abbreviations 145
Související produkty a manuály pro Příslušenství komunikace 2n M2M Solution 2N SmartCom - User Manual 1.9.0
(101 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce