2n M2M Solution 2N SmartCom - User Manual 1.9.0 Uživatelský manuál Strana 20
- Strana / 149
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
202N TELEKOMUNIKACE a.s., www.2n.cz
®
3.1 Putting in Operation
Operational state is 's main function. In this state, periodic data2N SmartCOM
®
readouts from input circuits are made. responds to queries from the2N SmartCOM
®
superior data concentrator, which can be the server, monitors the2N SmartCOM
®
events on the RS-232 / 485 / M-Bus interfaces and sends the acquired data to the
server via GPRS, or Ethernet in the case of the PRO ETH version.
Initialisation
Insert the PIN–disabled data SIM card in and connect the GSM2N SmartCOM
®
antenna and power supply as instructed in ., Mounting. Subs. 2.3
When the power supply is connected, the LED indicator on the upper2N SmartCOM
®
side of the module flashes three times quickly and then starts flashing in longer
intervals. Refer to . for LED status details. The GPRS module startsSubs. 3.2
communicating with the provider in about 10 seconds trying to log in and obtain the IP
address. The LED starts shining constantly to indicate a successful login.
Tip
2N SmartCOM
®
is working if the LED indicator is shining, thus
indicating a successful mobile provider connection and IP address
assignment.
To identify the IP address assigned by the mobile provider or perform 2N SmartCOM
®
the basic configuration upon power up, get connected via the serial port (RS 232). The
port is in the data mode upon power up, retransmitting all data from the input to the
GPRS network. Use the +++ sequence preceded and followed by a 1–second delay to
switch into the configuration mode. When your replies OK, start2N SmartCOM
®
configuring using the AT commands as listed below.
Restart the serial port to return to the data mode. To do so, you can either send the
ATO command or disconnect from the power supply.2N SmartCOM
®
Tip
can also be configured via Terminal Config. Refer to 2N SmartCOM
®
.S. 6
If you cannot use a PC, make the basic settings using SMS messages.
Refer to for details.S. 5
When your has been programmed as required, connect the device to2N SmartCOM
®
the available serial ports RS-232 / 485 / M-Bus. Launch the hyperterminal and get
connected to the public IP address via port 10000, which, together2N SmartCOM
®
with the serial port, can be used for configuring. Use port 10001 for retransmitting data
to RS-232 and port 10002 for retransmitting data to RS-485 / M-Bus.
- 2N SmartCom 1
- 1. Product Overview 5
- 1.1 Product Description 6
- 1.2 Upgrade 8
- 1.3 Terms and Symbols Used 9
- 2.1 Basic Version Description 11
- 2.2 PRO Version Description 13
- 2.3 Before You Start 15
- 2.4 Mounting 16
- 3. Function and Use 19
- 3.1 Putting in Operation 20
- 3.2 GSM LED Indicator 21
- 3.3 Input and Output Circuits 22
- Output Circuits 23
- IP Access 24
- Real Time Clock 25
- Wireless M–Bus Interface 25
- ZigBee Interface 26
- 3.4 Input Calibration 27
- 4. Configuration by Terminal 29
- 4.1 Configuration 30
- 2N SmartCOM GSM Commands 32
- Port 1 (RS 232) SC Commands 34
- Relay Outputs 36
- ADC – Input Circuits 38
- S0 – Pulse Counting 41
- General Commands 43
- Test Command 46
- 5. Configuration by SMS 58
- INFO SMS 59
- Basic Settings 60
- Relay Control 62
- Error Replies 64
- 6. Terminal Config 66
- Application Details 67
- Application Use 70
- Figure: Ethernet Menu 71
- Figure: IP Access Menu 77
- 7. Control Panel 78
- 7.1 SC Server 79
- Licencing 80
- 7.2 Control Panel 82
- Introduction to Application 84
- Figure: Application Window 85
- Basic Controls 86
- 7.3 Control Panel Use 88
- Connections 90
- Virtual Ports 92
- Settings 94
- Admin Mode 96
- Terminals 99
- Server Settings 101
- Firmware Management 103
- 8. AT API 107
- 8.1 AT API Description 108
- 8.2 Supported Commands 109
- Terminal Connection 111
- Terminal Communication 111
- Port Settings 112
- Terminal Data Reading 113
- 9. User Defined Functions 117
- 9.1 UDF Description 118
- 9.2 UDF Condition Setting 119
- Action Types 121
- Action Parameters 123
- Counters 125
- Error Codes 125
- 10. sc_config 128
- Database Export and Import 129
- Setting Options 130
- 11. Maintenance 134
- 11.2 Factory Default Reset 136
- 11.3 Repairs 137
- 12. Technical Parameters 138
- Power Supply 139
- Relays (Two) 139
- Input Circuits to ADC (Two) 140
- RS232 Interface 140
- Working Conditions 140
- CE certificate 143
- 13. Supplementary 144
- Information 144
- 13.1 List of Abbreviations 145
Související produkty a manuály pro Příslušenství komunikace 2n M2M Solution 2N SmartCom - User Manual 1.9.0
(101 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce